New Holland 5060 Baler Owners Manual

Download >>> https://imgfil.com/1vj307

The string in the left knotter that was missing did not have a knot on either end of the string Before the next baling i rechecked the adjustments - coiuldnt see anything that look out of adjustment or differnet from the right side that was working well.. Well ship it direct to you, letting you save up to 70 off prices youd pay at the New Holland dealer.. Our customer support staff is the best around and you can ask questions in our QA community get help from experienced mechanics and enthusiasts.. What happens if you cant find the exact part your need Not to worry- let us know by filling out our parts request form and well ask our network of suppliers and yards if they can get it to you- even if its a used Ford or New Holland part.. It had a 4-cylinder, vertical Hercules engine which would start on gasoline and run on kerosene, the transmission was three speed and it had a worm-gear final drive.. Our parts are back by an industry leading warranty and well also help you find answers to your replacement part questions.. Appreciate if anyone has any suggestions on what parts may be faulty or other adjustments that I might have to make.. The name Fordson was the contraction of the companys name and by January 1918 it had been registered as a trademark.. At this point it was getting late in the day and had to finish baling so I switched back to sisal on the left side.. I can tighten further to get more tension but at that point is flattening the twine between the two plates and it is impossible to pull the knot between the two balls through the plates.. I am going to try and borrow a go pro style camera and mount on the left knotter are so I can try and see what is happening I am not sure what to try next.. I checked the twine box tension with a fish scale - had less than a pound with plastic twine - tried to set to 3 to 4 pounds but I had to tighten it where there spring was fully compressed to get to close to 3 pounds and then it was so tight the the knots in the string where the balls were joined would not pull through the tension plates.. Henry Ford started producing this tractor in April 1918 for the U S Fordson name was found on the upper radiator panel while the name of Henry Ford Son was stamped into the fuel tanks end.. Simply choose your model from the dropdown above and well show you our expansive list of new replacement parts.. I had to bck off a little till there was enough movement in the top plate to let a knot pass.. Problem is I tightened it till the spring was fully compressed and still only get 3 pounds using a fish scale.. Baled 400 bales after the switch to sisal and it only missed one knot on the left side with sisal and one on the right side with the plastic twine.. Thinking ahead is the best way to be safe and avoid taking any chances You must have JavaScript enabled in your browser to utilize the functionality of this website.. Here you will find a wide selection of parts for every type of tractor or machine made by Ford or New Holland.. Did I mention prices For all your Ford or New Holand parts needs, we sell them at up to 70 less than what you might pay at the dealer.. A reply back would sure help the next person with a similar problem If this doesnt fix it, there is a bit more to check, adjust, bend, or replace.. Later on, the buyer as revealed to be Henry Ford who was now the only owner of the enormous Ford Motor Company.. We have quality products, great prices and the best support available anywhere These tractors had no identifications and they came to be known as MOM tractors, due to the fact that they had been built for the Ministry of Munitions in England.. The engine, the final drive, and the transmission case worked as a frame Magnets were used for the ignition, these were on the flywheel, and to cool the engine the water was circulated by a thermo-siphon system.. This is the force level needed to yank the tine from the twine box alone Measure with a fish scale or a bag of sugar, doesnt matter to me what you use.. To this day, the 2N, 8N, and 9N, are staples of American agriculture The Ford Motor Company produced some of our countrys finest tractors, which is why people are still running them and coming to TractorJoe to get Ford tractor parts and NH parts direct to their door.. Take a gander at the existing force levels before you start to see if all this makes sense so far.. Usually a couple of slipper plates and some wing nuts and springs involved Twine disk hold force.. Tired baling again yesterday 2 new rolls of 9000 ft pastic twine installed - same problem - left knotter was missing frequently - I had read in one forum to try reducing the twine holder tension if there was no knot on both ends of the twine - I loosened the bolt 14 turn at a time - after half a turn looser it was a little better but still missing every 10 or 12 bales.. We sell only the best tractor parts for major brands like Ford and New Holland Whether you need a new driveshaft, a new clutch, a new radiator for your Ford or New Holland tractor, TractorJoe has got what you need.. Sometimes owners mistakenly pick up a box of round bale twine and even overseas suppliers cheat on the thickness and strength characteristics of their products (Thats a GLOBAL benefit of using shady international trade some of you may have already found out about.. Ive seen incredible thickness variation even in brand name twine, too WTF Id re-thread the machine, too, because using two new bales will (hopefully) keep you from running out 12 way through using one side.. On top of that, well send it right your door using our fast and secure shipping service.. This keeps the twine in the needle groove under control of the tucker fingers and makes sure it lands in the twine disk and stays there.. Did the following I installed new bolted twine knifes new twine holder springs new brass rollers on twine knife arms replace twine box tension plates set twine disc timing adjusted twine fingers adjusted knife arm to bill hook clearance (slightly rubbing) I loaded with 9000 ft plastic twine and did the first baling of the year last week - I baled about 60 bales with no misses and then it started to miss but always on the left side ( side opposite the twine box) It gradually got worse over the next 100 bales to the point where it was missing a bale about every 5 or 6 bales on the left side.. Thats another good check: Both sides should start the spare twine ball at about the same time to show you that bale tension and packing is nice and even.